Putty Acrylit-406 interior & ndash; water-dispersion latex latex filler. Ecologically clean product, does not contain toxic solvents.
Scope of application
Suitable for indoor use in dry rooms. Serves for leveling surfaces and fixing irregularities, ideally prepares the surface for painting and wallpapering. With the help of a special composition, a uniform continuous coating is created on concrete, cement and gypsum surfaces. Putty is used for finishing the dry surfaces before painting, applying decorative plaster or other finishing materials. The putty is ready for use and does not require dilution with water.
The putty is ready for use and does not require dilution with water.
Properties and Features
- resistant to dry abrasion
- is well polished
- Shrinkage
- has good adhesion to wood, concrete, brick, plaster, etc.
- the puttying coating has a high coefficient of vapor permeability, ensures correct air and moisture exchange;
- when applied to vertical surfaces, it does not drip from the spatula, it is easily applied and distributed over the surface
- after drying does not melt, gives a strong smooth matte surface.
Flow
0.5-2 kg/m² - depending on the application thickness.
Specifications
Composition | An aqueous dispersion of an acrylic copolymer, a filler, modifying additives |
Drying time, h | Tack free 2 hours, complete drying 24 hours under normal conditions |
Coating appearance | A dense, homogeneous mass without foreign inclusions |
Density, g/sm³ | 1,75 – 1,8 |
Diluent | Water |
Consumption, kg/m² | 0.5-2 |
Solids,% | Not less than 75 |
Specifications | 2316-003-37557482-12 |
Color | White |
Warranty period of storage, months | 12 months |
Подготовка поверхности
Рабочая поверхность должна быть сухой и не иметь загрязнений. Отслаивающиеся старые покрытия должны быть удалены. Пылящие и сильно впитывающие поверхности предварительно укрепить грунтовкой «Акрилит-06».
Способ нанесения
Перед нанесением продукт следует тщательно перемешать. Шпатлевка готова к применению и не требует разбавления водой.
Шпатлевка наносится шпателем сплошным слоем с помощью нержавеющих или пластмассовых шпателей. Оптимальная толщина наносимого слоя внутри помещений – не более 3 мм. Допускается заделка неровностей глубиной до 7 мм. При больших неровностях рекомендуется многослойное нанесение шпатлевки. После полного отверждения шпатлевки, необходимо зашкурить поверхность шлифовальной шкуркой и обеспылить. После чего поверхность готова к дальнейшему окрашиванию. По окончании работ инструмент промыть водой.
Не рекомендуется наносить шпатлевку при повышенной влажности и температуре ниже +15°С.
Хранение
Водно-дисперсионные шпатлевки пожаро- и взрывобезопасны, не требуют специальных мер защиты. При работе соблюдать общие санитарные правила.
Транспортировать и хранить в плотно закрытой таре при температуре от 0 до +40°С. Выдерживает замораживание до -25°С, но не более пяти циклов замораживания-оттаивания. Шпатлёвку размораживают при температуре (20+-5°С и тщательно размешивают до получения однородной массы. Гарантийный срок хранения: 18 месяцев с даты изготовления.
Write a review
Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: