with spray gun
Strength
for wet cleaning
no more than 5%
is possible
A water-dispersive, highly technological and environmentally friendly elastic paint for facade and interior works. The paint is a white, viscous liquid. When applied, it conceals fine cracks in plasters, old coatings and prevents their appearance on the surface.
Scope of application
It is designed to create an elastic, water-resistant and wash-resistant decorative protective coating that can be used in wet rooms, on facades loaded with water. High elasticity and filling (dry residue of not less than 70%) make it possible to cover fine cracks (up to 1.5 mm) during painting and during the operation of the coating to restrain the development of old (up to 3 mm) and the appearance of new cracks on the surface. It is used for external and responsible interior work on wooden, plastered, concrete (including foam concrete), brick and other mineral surfaces in all types of buildings and structures.
Properties and Features
- has good adhesion to almost all bases: plaster, cement, concrete, asbestos, wood, chipboard, brick
- hides small wall defects (restrains cracks up to 3mm)
- has good hiding power, elasticity (elongation of at least 300%), flexibility
- has a high vapor permeability;
- has a high water, weather and wear resistance
- lightfastness (does not turn yellow during operation)
- good dirt repellent properties
- the paint is easy to use when painting vertical surfaces: it does not drip, it is easily applied and shaded
- Depth of relief up to 1mm;
- tinting is possible in any color.
Flow
200 g/m² - until full cover
Specifications
Composition | |
Drying time to degree 3 at t (20±2)°С, h. | |
Coating appearance | |
Mass fraction of solids,% | |
Operating temperature range of application, °C | |
Density, kg/l | |
Consumption, kg/m² | |
Milling degree on the device "KLIN", mkm | |
Hiding power of the dried film, g/m² | |
Relative viscosity-246 (6 mm), of not less than | |
Color | |
Warranty period of storage, months |
Подготовка поверхности
Поверхность очистить от грязи и пыли, непрочно держащееся старое покрытие необходимо удалить. Подготовленная поверхность, должна быть сухой, чистой, не осыпающейся. С целью укрепления поверхности и улучшения адгезии рекомендуется использовать грунтовку для фасадов и интерьеров (пропиточный состав АКРИЛИТ-06 глубокого проникновения).
Способ нанесения
Перед применением краску тщательно перемешать. Продукт не смешивать с другими лакокрасочными материалами и органическими растворителями. Наносится краска кистью, валиком или краскопультом. Рекомендуется двукратное нанесение краски. Окрасочные работы необходимо проводить в сухую погоду при температуре не менее плюс 5°С. После окончания окрасочных работ, инструмент сразу промыть водопроводной водой. Не рекомендуется окраска внешних поверхностей в дождливую погоду, при повышенной влажности и при обледенении поверхности. ! Возможно применение краски совместно с эластичной штукатуркой «Акрилит-415» по специальной технологии (по ОСП-панелям и др. поверхностям).
Хранение и транспортировка
в герметично закрытой таре при температуре от +5ºС до +40ºС. Выдерживает замораживание до -25°С, но не более 5 циклов замораживания-оттаивания.
Write a review
Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: